Farm King Grain Handling Brochure

Public / Brochures

2477 views
0 Likes
0 0

Share on Social Networks

Share Link

Use permanent link to share in social media

Share with a friend

Please login to send this document by email!

Embed in your website

Select page to start with

1. Grain Augers | Grain Cleaners | Roller Mills | Hammer Mills GRAIN HANDLING

22. PRODUCTS FOR EVERY FARM DID YOU KNOW WE HAVE

23. GRAIN HANDLING TILLAGE APPLICATION EQUIPMENT HAY TOOLS LANDSCAPING EQUIPMENT ALLIED COMMERCIAL EQUIPMENT Visit farm-king.com for the latest info

24. farm-king.com For more information contact: E-mail: info@buhler.com farm-king.com Equipment shown is subject to change without notice. ©2017 Buhler Trading Inc. Printed in Canada. TSX:BUI Ref: 112017 a division of Buhler Industries Inc.

3. TABLE OF CONTENTS Backsaver Augers 10" / 13" / 16" ....................... 4 Conventional Augers / 8" / 10" .................... 10 Movers And Hoppers ...... 14 Rollermill .......................... 16 Hammermill ..................... 17 Utility Auger ..................... 18 Unloading Auger .............. 19 Crain Cleaner .................... 20 CX

12. OPERATION All augers may be elevated up to 45°; however, for the best operating efficiency, 35° should not be exceeded. At angles over 35° the capacity and life of the auger decreases. Use in some types of fertilizer may cause accelerated wear and corrosion as well as added stress on lift components due to additional load. Use in fertilizer can affect warranty. Run auger partially full until flighting becomes polished. Never operate an empty auger for over one minute, as the flighting and housing will experience excessive wear. To position the auger, always tow or move the auger in the down position to a point as close as possible to the bin or barn. Be sure the wheels are free to move and no one is standing close to the auger when raising or lowering. Never attempt to raise or lower the auger while it is in operation. The intake auger swivels freely on the top of the input box. It can be positioned anywhere between the tractor and the side of the auger. The distance between the tractor and the auger stubs should be between 36" and 38" with the tractor and auger on level ground and the auger in full down position. This distance is obtained by either adjusting the tractor hitch, the auger hitch or both. Before engaging PTO, start tractor and idle engine. Engage PTO slowly and bring PTO rpm up to recommended speed of 500 rpm for 13" augers. Before stopping auger (except in an emergency) let all grain empty out of the auger, idle engine then disengage PTO. Shut off tractor. One way flow control valve (#71) can be adjusted by loosening the hex nut on the side, and turning on the screw with the machined end. Turning the screw in decreases the speed the auger lowers, while turning it out increases the speed. For the 13" x 70' auger, the approximate initial setting should be three turns out from the tight position. For the 13" x 85' auger, the approximate initial setting should be five turns out from the tight position. When set, re-tighten hex nut to set position. NOTE: Be sure that the valve is somewhat open before raising the first time or auger will not lower. Be sure there is always some tension on the flighting by adjusting the end thrust bearing at the upper end of the auger. Be certain to turn jack sideways when towing auger. PTO shear bolts (2 required) 5/16" x 1" hex bolt (grade 8) Always use a flag, or at night, a signal light when towing an auger on a road. Check your local regulations for further safety devices in this regard. AUGER RECOMMENDATION FOR GRAIN BINS GRAIN BIN MODEL DIAMETER EAVE HEIGHT OVERALL HEIGHT AUGER LENGTH FEET METERS FEET METERS FEET METERS FEET 3006 29' 10" 9.10 22.2 6.76 30.5 9.31 60, 70, 80, 85, 95, 104 3008 29' 10" 9.10 29.5 8.99 37.9 11.54 70, 80, 85, 95, 104 3010 29' 10" 9.10 36.8 11.23 45.1 13.74 80, 85, 95, 104 3012 29' 10" 9.10 44.2 13.46 52.4 15.98 95, 104 4206 41' 9" 12.73 22.2 6.76 33.6 10.24 70, 80, 85, 95, 104 4208 41' 9" 12.73 29.5 8.99 40.9 12.47 80, 85, 95, 104 4210 41' 9" 12.73 36.8 11.23 48.1 14.65 95, 104 4212 41' 9" 12.73 44.2 13.46 55.4 16.89 104 4806 47' 9" 14.55 22.2 6.76 35.3 10.76 70, 80, 85, 95, 104 4808 47' 9" 14.55 29.5 8.99 42.7 13.00 85, 95, 104 4810 47' 9" 14.55 36.8 11.23 49.8 15.18 95, 104 4811 47' 9" 14.55 40.5 12.34 53.5 16.30 104 12 AUGER OPERATION

7. MEASUREMENTS MODEL >> 1050 1060 1070 1080* 1370 1385 1395* 1684 16104 Wheel track 9' 10' 12' 12' 12' 12' 12' 13' 4" 14' 6" A, height † - lowest - half way - highest 11' 2" 23' 6" 36' 11' 3" 27' 6" 43' 8" 12' 6" 30' 3" 48' 13' 6" 34' 3" 55' 13' 7" 31' 9" 50' 13' 8" 36' 6" 59' 6" 14' 8" 40' 6" 66' 4" 13' 2" - 57' 14' 10" - 77' 4" B, forward reach - lowest - half way - highest 26' - 18' 30' 3" - 22' 3" 35' 8" 33' 5" 27' 10" 45' 7" 41' 10" 34' 9" 36' 11" 33' 27' 5" 45' 4" 39' 8" 31' 10" 55' 4" 48' 3" 38' 9" 44' 10" 42' 33' 4" 57' 8" 52' 36' 1" † All measurements taken with 18" hitch height. ‘A’ lowest is overall transport height, half way and highest are spout to ground measurements. *includes 10' extension. SPECIFICATIONS MODEL >> 1050 1060 1070 1080* 1370 1385 1395* 13114 1684 16104 Size 10" x 50' 10" x 60' 10" x 70' 10" x 80' 13" x 70' 13" x 85' 13" x 95' 13" x 114' 16" x 84" 16" x 104' Tubing 12 gauge 12 gauge 1 and 2: 10 ga. 3 and 4: 11 ga. 1 and 2: 10 ga. 3, 4 and 5: 11 ga. Flighting (Measured from centre of flighting strip) 7 gauge 1/4" flighting in swing-away and main auger 1/4" on swing and main auger Flighting shaft 11 gauge, 2-3/8" diameter 11 gauge, 2-3/8" diameter - - Undercarriage 3" x 3" x 1/8" square tube 70' - 3-1/2" x 3-1/2" x 3/16" square tube; 85' and 95' - 4" x 4" x 1/4" square tube 5" x 5" x 1/4" square tube 5" x 5" x 1/4" square tube Lift arms 2" x 5" x 3/16" tube 1/4" formed tubing upper, 7 gauge lower 1/4" formed tubing Bridging 3/8" cable on 50' and 60' models, 1/2" cable on 70' and 80' models 1/2" cable Steel tube trussing Upper: 3/4" cable Upper:3/4" cable Side: 1/2" cable Wheels and hubs 15" with 5 bolt automotive type hubs and bearings 15" with 6 bolt automotive type hubs and bearings 6 bolt hubs, 11 L x 15 x 8 ply 6 bolt hubs, 11 L x 15 x 8 ply 8 bolt hubs, 16.5 L x 16.1 x 10 ply Swing auger drive Two internal gearboxes (PTO driven), sprocket and chain Two internal gearboxes (PTO driven), sprocket and chain - - Hopper dimensions 43-1/2" x 60" 43-1/2" x 60" 48" x 60" Standard hopper height from ground 15-1/4" at heel end, 14-1/4" at other end 16-3/4" at heel end, 16-1/4" at other end n/a n/a Multi-flighting hopper height from ground 11-3/4" at both ends 12-3/4" at both ends 13-1/2" 13-1/2" Tractor requirements - min PTO hp (with 540 RPM PTO) - approx. hydraulic requirements for lift 40 hp 1000 PSI 48 hp 1000 PSI 55 hp 1000 PSI 65 hp 1000 PSI 80 hp 1200 PSI 90 hp 1200 PSI 100 hp 1200 PSI 165 hp 1700 PSI 150 hp 1500 PSI 175 hp 1500 PSI Hitch weight - - 840 lb - 1140 lb 1270 lb - 2700 lb 2,200 lb 2,700 lb Weight 2,545 lb 2,987 lb 3,354 lb 3,622 lb 5,175 lb 6,381 lb 6,683 lb 15,500 lb 11,000 lb 13,000 lb FARM KING AUGERS FEATURE A TWO-YEAR PARTS WARRANTY. Model 1684 BACKSAVER AUGER

13. WHAT'S NEW The CX2 auger intake is now 24 inches allowing for greater capacity. Strengthened the holding brackets for the winch making it stronger and keeps the auger centred and true. Improved the engine mount: Now +/- 2 degrees when engaged. Incorporated a pedestal style control panel that allows the user to walk in the direction of travel and has an arm rest. Includes a battery hold down strap to secure the battery while in transport. Warranty covers 1st year parts & labour and 2nd year parts only. ISO 9001:2015 CERTIFIED C C X X QUICK UPDATES 13 AUGERS CX

2. Farm King Grain Handling: grain augers, grain cleaners, roller mill and hammer mill ISO 9001:2015 CERTIFIED FARM KING GRAIN HANDLING EQUIPMENT IS BACKED BY DECADES OF QUALITY BUILT PRODUCTS FOR JUST ABOUT EVERY AGRICULTURAL APPLICATION. Moving grain and commodities has never been easier than with the full line of Farm King grain augers, grain cleaners and unloading augers. These products are industry leaders because of their structural integrity and ease of use. Stop by your local dealer today and see how Farm King grain handling equipment can improve your bottom line. FARM KING PRODUCT LINE-UP FARM KING PRODUCT CATEGORIES Grain Handling Tillage Application Equipment Hay Tools Landscaping Equipment Allied by Farm King Commercial Products FARM-KING.COM

15. SPECIFICATIONS MODEL >> CX2-841 CX2-851 CX2-861 CX2-1041 CX2-1051 CX2-1061 1336 Tube width 8" 10" 13" Tube length 41' 51' 61' 41' 51' 61' 36' Wheel track 8' 9" 10' 1" 10' 1" 8' 9" 10' 1" 10' 1" 7' 5" Belt drives Double Double N/A Triple Triple Triple Triple Tube, gauge 14 14 14 12 12 12 12 Flighting, gauge 10 10 10 7 7 7 1/4" Flighting shaft, dia. 1-1/4" 1-1/4" 1-1/4" 2-3/8" 2-3/8" 2-3/8" 2-3/8" Flighting shaft, gauge 11 gauge 11 gauge 11 gauge 11 gauge 11 gauge 11 gauge 11 gauge Drive line 1-3/8" 1-3/8" 1-3/8" 1-3/8" 1-3/8" 1-3/8" 1-1/2" Gasoline - Motor pulley - Fuel tank capacity 3-1/2" 6.5 3-1/2" 6.5 N/A N/A 3-1/2" 6.5 3-1/2" 6.5 4" 6.5 3-1/2" N/A Motor pulley (tube-mount electric) 4 3-3/4" 3-3/4" 3-3/4" 3-3/4" 3-3/4" 3-3/4" 3-3/4" Recommended hp 16 hp 20 hp 24 hp 28 hp 32 hp 38 hp N/A 2 Fuel tanks are supplied with engine configuration only. 3 Tube reach is measured along the auger tube, from the tip of the intake guard to the gear box on the engine drive configurations. 4 Tube mount kits are recommended to be installed on direct PTO (CX or C) models using pulley diameters shown. Use a 6" motor pulley when installing electric motors on C series engine drive models. AUGER MOVER MODEL >> CX AUGER SIZE FEATURES CXM841 8" x 41' and under - Power Steering - Fuel Tank Capacity - 6.5 US Gal 3 - Central Control Location - Mover Mounts to Undercarriage only - Rear Wheel(s) Lift for Transport CXM851 8" x 51' and over CXM1041 10" x 41' and under CXM1051 10" x 51' and over CXM1061 10" x 61' and over C506 13" x 36' 3 Fuel tanks are supplied with engine configuration only. MEASUREMENTS MODEL >> CX2-841 CX2-851 CX2-861 CX2-1041 CX2-1051 CX2-1061 1336 A, up 27' 9" 35' 2" 42' 8" 28' 3" 32' 8" 39' 3" 19' 1" A, down 10' 8" 9' 11" 12' 5" 10' 5" 9' 6" 11' 11" 9' 9" B, up 12' 5" 17' 3" 20' 3" 13' 3" 16' 9" 20' 4" 13' 2" B, down 18' 8" 23' 10" 28' 9" 18' 3" 23' 5" 28' 6" 14' 3" D, direct drive 6' 5" 6' 7" 6' 9" 6' 4" 6' 6" 6' 8" 6' 7" D, electric & PTO drives 10' 11" 14' - 10' 11" 14' 16' 1" 10' 10" INTAKE HOPPER MODEL >> 8" 10" 13" Hopper dimensions 32" x 36" 32" x 36" 32" x 36" Height, to top of steel 10" 10" 10" Height, to top of rubber 14" 14" 14" Caster jack lift capacity 2000 lb 2000 lb 2000 lb Reach, approx. 1 108" 108" 108" Capacity 2 3487 bu/hr 5552 bu/hr - Weight 200 lb 200 lb 200 lb 1 Reach is measured from the end of intake hopper to first obstruction on the auger tube 2 Capacity will vary by grain conditions and by elevation of the main auger - tested on a 10" auger at 31.6° elevation,using dry #2 Corn (<13% moisture) CONVENTIONAL AUGER • 17 15 AUGER MOVERS AND HOPPERS

16. ROLLERMILLS ARE DESIGNED TO MAXIMIZE THE NUTRITIONAL VALUE OF FEED. Available in three sizes, Farm King rollermills are capable of processing up to 300 bushels per hour. A manual feed gate sets the flow into the rollermill and the adjustable tensioner determines the thickness of finished grain. Double leaf springs ensure constant, even roller pressure. Machine-grooved rollers are available in steel or chrome and can be inexpensively re-machined up to three times if damaged or worn. An optional magnet removes nails and other metal objects from the grain and prevents them from damaging the rollers. An electric motor or PTO drives the 85 and 100. The 180 is PTO driven and can be equipped with a transport with 15" wheels and a 12' hydraulic discharge auger that swings a full 180 degrees. ROLLERMILL ROLLERMILL PRODUCT OVERVIEW Machine-grooved rollers are available in steel or chrome Manual feed gate determines the thickness of finished grain FEATURES Capable of processing up to 300 bushels per hour Available in three sizes Double leaf springs ensure constant, even roller pressure OPTIONS Optional magnet removes nails and other metal objects from the grain 15" wheels and a 12' hydraulic discharge auger ROLLERMILL 85 100 180 Size 7" x 8" 10" x 10" 18" x 10" Roll diameter 8" 10" 10" Grooves per inch 8 (6 corn) 8 (6 corn) 8 (6 corn) Roll pressure Double leaf spring Capacity (approx.) 50-100 bu/hr 100-150 bu/hr 200-300 bu/hr Magnet Optional Optional Optional Drive required PTO or 3-5 hp electric PTO or 5-7.5 hp electric 40-60 PTO hp Discharge auger Not available Not available Optional Tires Not available Not available Optional Stationary stand Optional Optional Optional Weight 225 lb 317 lb 540 lb Scrapers Optional Optional Standard 16 ROLLERMILL

17. HAMMERMILL PRODUCT OVERVIEW Manufactured with high quality carbon steel Grinds as much as 75 bushels per hour Sliding feed gate controls the amount of grain entering the mil FEATURES Can be reversed for use in four different positions Grinds as much as 75 bushels per hour Adjustable motor mount fits most 5 to 7.5 horsepower electric motors OPTIONS Discharge hopper makes it easy to move processed grain Optional magnet removes nails and other metal objects from the grain DRIVE-OVER HOPPER • 19 HAMMERMILLS DELIVER TOP-QUALITY PROCESSED GRAIN WITH MINIMUM MAINTENANCE AND LOW OPERATING COSTS. Grinding grain fresh every day means animals get the most nutritional value. A Farm King hammermill does the job quickly and economically, grinding as much as 75 bushels per hour. An adjustable motor mount fits most 5 to 7.5 horsepower electric motors. The sliding feed gate controls the amount of grain entering the mill and an optional magnet removes nails and other metal objects from grain and prevents damage to the hammermill. An optional discharge hopper makes it easy to move processed grain. The hammers are made from high quality carbon steel for extra-long life. They can be reversed for use in four different positions for even longer wear. HAMMERMILL HAMMERMILL 60 Working width 6" Drive Double-V pulley Motor required (approx.) 5 - 7.5 hp, 3450 rpm motor (not included) Capacity (approx.) 75 bu/hr Hammers 18, C1045 carbon steel Rows 6 Screen size 6" wide x 14" round Height 36" (including hopper) Width 24" Depth 19" Weight 145 lb The optional magnet removes nails and metal debris from grain. 17 HAMMERMILL

4. BACKSAVER AUGER PRODUCT OVERVIEW Manufactured for high-capacity with heavy-duty construction Full height of up to 77' 40 to 175 hp required FEATURES Swing away auger with a self-leveling hopper Hydraulic mechanical linkage Scissor lift undercarriage Working and travel light kits OPTIONS Hydraulic winch and hopper mover (std on 16" models) BACKSAVER AUGER 10", 13" AND 16" MODELS SELF-LEVELING The self-leveling hopper on the swing-away auger will remain level regardless of auger height. The unique design allows the intake hopper to be loaded on uneven terrain. Increased flexibility relieves the hopper of unnecessary down pressure on all hopper parts. SWING-AWAY AUGER The swing-away auger can be positioned on the right side or left side of the auger, adding flexibility for yards with limited space or restricted access. An optional power mover uses two hydraulic motors that move the swing- away auger, limiting the physical labor required. HYDRAULIC CYLINDERS Powered by a heavy-duty hydraulic cylinder (two on model 13114, shown), the unique scissor lift undercarriage is capable of holding the auger at a 44° angle when fully extended. With the cylinders completely compressed, the auger angle changes to 5° in transport mode. HYDRAULIC CONTROLS Using the auger-mounted hydraulic controls, the swing away auger can be lifted into position for transport and the hopper can be moved back and forth. This system removes most of the physical labor that was once required during grain handling. [1] 4 BACKSAVER AUGER

10. CONVENTIONAL AUGER PRODUCT OVERVIEW Manufactured for high-capacity with heavy-duty construction Wide stance undercarriage Lengths of up to 61' FEATURES 7 gauge flighting in 10" models Heavy-duty reversible gearbox OPTIONS Multiple drive options available Poly spout and poly hopper CONVENTIONAL AUGER CX SERIES - 8" AND 10" MODELS UNDERCARRIAGE The wide stance of the undercarriage improves stability and is constructed with square tubes to enhance strength and durability. In addition to being well balanced, the undercarriage features automotive-type hubs and bearings that improve ease of handling. TOP DRIVE The top drive is housed in a sealed grease bath and features a chain-tightener. The components in the sealed oil bath are resistant to heat, dust, debris and moisture, reducing maintenance and enhancing the longevity of the chain and sprockets. TRANSPORT The sturdy lightweight assembly allows the conventional auger to be easily transported. The trailing swivel wheels can be raised hydraulically to allow for increased turning radius as well as smooth transitions over uneven terrain. DRIVE OPTIONS Several drive options are available, including direct PTO, belt-drive PTO, gas engine drive, and electric motor drive matched to a belt or direct drive. ENGINE MOUNT The new engine mount has no moving parts for easy set up. The engine is leveled by the belt guard system which [1] 10 CONVENTIONAL AUGERS

14. SPECIFICATIONS MODEL >> CX2-841 CX2-851 CX2-861 CX2-1041 CX2-1051 CX2-1061 1336 Tube width 8" 10" 13" Tube length 41' 51' 61' 41' 51' 61' 36' Wheel track 8' 9" 10' 1" 10' 1" 8' 9" 10' 1" 10' 1" 7' 5" Belt drives Double Double N/A Triple Triple Triple Triple Tube, gauge 14 14 14 12 12 12 12 Flighting, gauge 10 10 10 7 7 7 1/4" Flighting shaft, dia. 1-1/4" 1-1/4" 1-1/4" 2-3/8" 2-3/8" 2-3/8" 2-3/8" Flighting shaft, gauge 11 gauge 11 gauge 11 gauge 11 gauge 11 gauge 11 gauge 11 gauge Drive line 1-3/8" 1-3/8" 1-3/8" 1-3/8" 1-3/8" 1-3/8" 1-1/2" Gasoline - Motor pulley - Fuel tank capacity 3-1/2" 6.5 3-1/2" 6.5 N/A N/A 3-1/2" 6.5 3-1/2" 6.5 4" 6.5 3-1/2" N/A Motor pulley (tube-mount electric) 4 3-3/4" 3-3/4" 3-3/4" 3-3/4" 3-3/4" 3-3/4" 3-3/4" Recommended hp 16 hp 20 hp 24 hp 28 hp 32 hp 38 hp N/A 2 Fuel tanks are supplied with engine configuration only. 3 Tube reach is measured along the auger tube, from the tip of the intake guard to the gear box on the engine drive configurations. 4 Tube mount kits are recommended to be installed on direct PTO (CX or C) models using pulley diameters shown. Use a 6" motor pulley when installing electric motors on C series engine drive models. Available for the 8" and 10" CX auger lineup, the completely redesigned mover incorporates power steering, hydraulic scissor lift for the intake, sport tread tires, hydraulic winch for auger height adjustment, improved engine mount and leveling systems and longer reach on the intake tube. Many parts have been standardized across the models and the kit is designed for ease of assembly, ease of operation and high maneuverability. CONVENTIONAL AUGER MOVER The self-leveling Conventional Auger Hopper adds versatility and convenience to your Farm King auger by giving you a powered intake hopper. The hopper is powered by the rotation of the existing auger core - no new drive mechanisms are needed. With a total reach now extended to approximately 108", this hopper allows you to cleanly collect the discharge of gravity wagons, grain carts, hopper bottom bins, grain trucks, highway grain trailers and more with no spillage, and no need to wrestle with removable hoppers. HAND-CRANK & CASTER JACK An optional hand-crank caster jack allows you to lift the intake hopper with ease, and maneuver the auger intake into position with minimal effort. TRANSPORT The hopper has a transport stabilizing bar and hitch for quick transport setup without the need to remove the hopper itself. A rubber skirt helps reduce grain spillage. CONTINUOUS VELOCITY JOINT A continuous velocity joint connects the hopper flighting to the main auger flighting, allowing the hopper to be powered with no new power source or hydraulic systems. INTAKE HOPPER MOVER CONTROLS The auger mover controls are located near the engine controls, allowing for one location control. The belt guarding doubles as the engine leveling device, which keeps the belts at the same tension in any auger position. CASTER WHEEL The unique caster wheel design and independently powered drive wheels allow an extremely short turn radius. The intake end scissor lift allows a wide range of vertical motion and tucks up under the auger tube for easy transport. ENGINE MOUNT The engine mount plate has no moving parts for ease of set up. The engine drive sheave is now standard equipment. The drive belts are engaged via a newly designed lever accessible from the auger and engine control location. 14 AUGER MOVERS AND HOPPERS

9. [1] 15' transport height and standard road lighting kit. The 16.5L x 16.1 tires are rated for intermittent highway usage and come with 8-bolt rim design. [2] The 1/2" and 3/4" cables create a bridge design to help maximize stability and even weight distribution. Cables can be tightened and loosened according to operator preference. With the auger reaching up to 104' in the air, stability and precise maneuverability is paramount when positioning the auger. [3] An unprecedented ground-to-spout height of 77' allows the Farm King 16104 to supply even the largest bins. With such a large reach, the 16104 is constructed with 5" x 5" thick steel tubing and a 14 1/2' outside wheel track assist in the stability and solid foundation during operation. [4] The dual flighting hopper and 16" tube means the 16104 Backsaver auger is ideal for hopper bottom trailers. Fully lifted, the 16104 Backsaver auger has a ground-to-spout height of 77', but drops to clearance height of less than 15' when in the lowered position. [2] [1] [3] [4] BACKSAVER AUGER • 13 BACKSAVER AUGER 16" Models THE 16" FARM KING GRAIN AUGERS ARE DESIGNED BY THE PEOPLE WHO KNOW AND UNDERSTAND YOUR GRAIN HANDLING NEEDS. The large 16" tubing by up to 104' length allow the operator to move large quantities of grain in short periods of time. Equipped with a 3" flighting shaft, the Farm King auger handles even the dampest crops with ease. BACKSAVER AUGER 16" MODELS PRODUCT OVERVIEW Manufactured for high-capacity with heavy-duty construction Model 1684 ideal for shorter bins and smaller yards Lengths of up to 104' 150 to 175 PTO hp required FEATURES Swing away auger with a self-leveling hopper Scissor lift undercarriage Hydraulic winch to lift the hopper into transport position Hydraulic hopper mover Load carrying tapered thrust bearing Dual flighting low-profile hopper 9 BACKSAVER AUGER

5. THE FARM KING BACKSAVER AUGER IS DESIGNED BY THE PEOPLE WHO KNOW AND UNDERSTAND YOUR GRAIN HANDLING NEEDS. With 10", 13" and 16" tubing by up to 104' length, the operator is able to move large quantities of grain in short periods of time. Transporting the auger has never been easier with a maximum transport height of 15'. HYDRAULIC WINCH An hydraulic winch easily lifts the hopper into place for transport. The lever and hydraulic valve are mounted to the main auger tube for easy access. Standard on model 16104 and optional on 10" and 13" Backsaver models. HYDRAULIC HOPPER MOVER The standard hydraulic hopper mover adds a powerful hydraulic motor to each of the inside wheels on the swing away hopper so the hopper can be positioned easily and with minimal effort. The control lever for the mover is mounted on the intake auger tube for easy access. Optional on 10" and 13" models. HYDRAULIC DRIVE WHEELS Each 16104 Farm King auger comes standard with a hydraulically controlled intake hopper. By simply moving the hydraulic lever, the intake hopper can be moved into precise position under hopper bottom and end dump trucks. Optional on 10" and 13" models. [6] [2] [3] [4] [5] [1] Hydraulic controls [2] Self-leveling [3] Hydraulic hopper mover [4] Hydraulic cylinders (model 13114 shown) [5] Hydraulic winch [6] Hydraulic drive wheels 5 BACKSAVER AUGER

21. FARM KING BUILDS TWO GRAIN CLEANER MODELS THAT ARE DESIGNED TO SEPARATE THE DOCKAGE FROM GRAIN WITH A TWO-STAGE SCREENING SYSTEM BEFORE IT GETS SHIPPED OR STORED, INCREASING PROFIT IN A VARIETY OF WAYS. þ Dockage reduces bin storage capacity and increase shipping costs. þ Cleaned grain dries faster. þ Screenings can be used as animal feed. GRAIN CLEANER • 23 The Model 360 can clean up to 1000 bushels per hour. The screenings are discharged onto the ground while cleaned grain is distributed through a built-in chute for convenient loading. The pulleys and adjustable mounts and are designed to fit most 1 hp motors. An optional 6" intake auger for easy loading. The Model 480 cleans up to 2500 bushels per hour, depending on moisture content and the amount of dockage. Trash and fines are thoroughly removed from the grain, with the fines being separated from larger screenings and are unloaded from separate chutes. An optional trash pan is available for collecting screenings. SPECIFICATIONS MODEL >> 360 480 Drum diameter / length 36" / 73" 48" / 98" Total length 97" 144" Width (outside of tires) 55" 76" Motor required (approx.) 1 hp 1 hp Drive Belt Belt Capacity 1000 bu/hr 2500 bu/hr Weight 493 lb 1,020 lb Weight, w/opt. trash pan n/a 1,253 lb Intake auger (optional) 6" 6" SCREENS >> INNER CONE ( standard ) INNER CONE ( large/small ) OUTSIDE DRUM ( standard ) OUTSIDE DRUM ( large/small ) Corn 5/8 x 5/8 x 17 ga. Small - 2 x 2 x 19 ga. 4 x 4 x 23 ga. - Wheat 4 x 4 x 23 ga. Large - 3 x 3 x 21 ga. 8 x 8 x 27 ga. Large - 6 x 6 x 25 ga. Sunflower 2 x 2 x 19 ga. Large - 5/8 x 5/8 x 17 ga. 6 x 6 x 25 ga. Small - 8 x 8 x 27 ga. Large - 5 x 5 x 24 ga. Soybean 2 x 2 x 19 ga. Small - 3 x 3 x 21 ga. 5 x 5 x 24 ga. Small - 6 x 6 x 25 ga. Milo 4 x 4 x 23 ga. Small - 5 x 5 x 24 ga. Large - 3 x 3 x 21 ga. 8 x 8 x 27 ga. Large - 6 x 6 x 25 Flax 4 x 4 x 23 ga. Small - 5 x 5 x 24 ga. 10 x 10 x 29 ga. - [4] [5] [6] [7] Model 480 shown w/opt. trash pan An intake auger is optional with a 6" for model 360 and 8" for model 480. 21 GRAIN CLEANER

8. [2] [4] [5] [1] Safety locking ball valve restricts hydraulic lines from losing pressure. [2] Load carrying tapered thrust bearing supports the weight of the flighting with auger in upright operating position. [3] Cleanout is simplified with an optional reverse kit and an underside access panel. [4] Durable 11 gauge flighting is used on every 10" and 13" model. [5] 11' to 15' transport height and standard road lighting kit. [6] Hydraulic Winch - An optional hydraulic winch easily lifts the hopper into place for transport. The lever and hydraulic valve are mounted to the main auger tube for easy access. [6] [1] [3] FARM KING BACKSAVER AUGERS ARE PRACTICAL, ECONOMICAL AND DEPENDABLE. That dependability has been a benchmark of Farm King Backsaver Augers for many decades. Auger tubing sizes are available in 10" or 13" diameters and lengths ranging from 50 to 114 feet. The 43-1/2" x 60" intake hopper invites large quantities of grain to be quickly moved up the auger and into the bin. BACKSAVER AUGER Models 10" and 13" 12 • BACKSAVER AUGER BACKSAVER AUGER 10"/13" MODELS PRODUCT OVERVIEW Manufactured for high-capacity with heavy-duty construction Lengths of up to 95' 40 to 100 PTO hp required FEATURES Swing away auger with a self-leveling hopper Scissor lift undercarriage Load carrying tapered thrust bearing OPTIONS Hydraulic winch to lift the hopper into transport position Hydraulic hopper mover Dual flighting low-profile hopper 8 BACKSAVER AUGER

20. GRAIN CLEANER PRODUCT OVERVIEW Separates the dockage from grain before shipping / storing Cleans up to 1000 bu/hr with the model 360 and up to 2500 bu/hr with model 480 FEATURES Two-stage screening process Larger intake spouts for easy filling OPTIONS Trash pan for collecting screenings (model 480) 6" intake auger (model 360) 8" intake auger (model 480) 22 • GRAIN CLEANER GRAIN CLEANER MODELS 360 AND 480 CLEANING PROCESS A two-stage screening process includes an inner cone screen for large trash and an outer drum screen for fines. Cleaned grain is emptied through a built-in chute. MOVE TRASH An optional trash pan can be added to model 480 which collects the fines and with a built-in auger, moves the trash to one end of the cleaner. It is then loaded into a trash pan for easy cleanup. PRECISE PLACEMENT The utility auger slide bar allows the auger to be placed in transport mode or positioned directly over the intake spout. UNLOAD CLEAN GRAIN A large unloading chute located at the back of the grain cleaner transports the cleaned seed out of the drums and into the auger hopper. TRANSPORT The intake auger can be swiveled around to the side of the cleaner and securely attached for transport. 15" wheels and a full frame transport are included. INTAKE AUGER An intake auger is optional on all models. A 6" utility auger is available for model 360 in lengths of 11', 16' and 21'. Model 480 has an 8" x 11' utility auger. [1] [2] [3] Two-stage screening process which includes an inner cone screen for large trash and an outer drum screen for fines. Multiple screen options for multiple crop sizes. Hitch and wheels make for a portable grain cleaner. Front adjustable legs to increase or decrease product flow. 1-1/4' and 2' intake spouts on models 360 and 480 respectively. 20 GRAIN CLEANER

11. THE NEW CX SERIES OF CONVENTIONAL AUGERS FROM FARM KING ARE AVAILABLE IN LENGTHS OF 41', 51' AND 61' IN BOTH 8" AND 10" DIAMETERS. The augers feature several enhancements to serviceability and stability and an expanded list of options. Several components have been standardized and redesigned to reduce repair and assembly time as well as to facilitate upgrades. The engine mount and leveling systems have been redesigned to ensure perfect belt tension at any auger position. CONVENTIONAL AUGER • 15 [1] Wide stance undercarriage [2] Transport (shown with optional auger hopper [3] Top Drive [4] Intake [5] Poly Hopper [6] Poly Spout [7] Hardened steel square tubing frame [3] [4] [2] [5] [6] [7] ensures perfect belt tension at every auger position - the separate leveling rod has been eliminated. POLY SPOUT AND HOPPER Flexible poly spout for accurate bin filling is optional. Also optional is a poly hopper to minimize spillage. INTAKE The intake end of the auger flighting is supported by a wooden, self lubricating bushing, which is highly resistant to dirt contamination and is maintenance free. A narrow safety guard and removable clevis hitch improve access to bins with small auger ports. FRAME Hardened steel square tubing frame provides a solid foundation. WHEEL SPINDLES The wheel spindles are now a bolt-on style, allowing easy set up and replacement. This also helps facilitate the auger mover installation. THE ALL NEW CX 11 AUGERS CX

18. UTILITY AUGER PRODUCT OVERVIEW 5' and 10' extensions 10 or 12 gauge flighting 3/4" or 1" sealed top bearing FEATURES Adjustable motor mounts Auger pulleys are standard The intake flighting is protected by an intake guard OPTIONS Poly hopper / Flow control CAGE A spider cage protects the intake flighting and belt guards are standard on all augers. GRAIN CLEANER The utility auger can be fastened to the grain cleaner to provide ease of transport and versatility. [1] Undercarriage, 10" model shown [2] Gearbox [3] Adjustable light SPECIFICATIONS MODEL >> 4" 6" 8" Auger lengths 11' / 16' / 21' 11' / 16' / 21' 11'* / 16' / 23'* Extension lengths 10' 10' 5', 10' Power 1/2 - 1 hp 1 - 4 hp 3 - 10 hp Auger tubing 16 gauge 16 gauge 14 gauge Flighting 12 gauge 12 gauge 10 gauge * Non-extendable Motor Mounts - Standard adjustable motor mounts mean that Farm King utility augers can be paired with various sizes and brands of electrical motors. Extensions - Heavy-duty flange and square coupler connect these tubing extensions. [1] [2] [3] 20 • UTILITY AUGER UTILITY AUGER 4", 6" AND 8" MODELS FARM KING MANUFACTURES A WIDE SELECTION OF UTILITY AUGERS, IN TUBE WIDTHS RANGING FROM 4" TO 8", AND IN LENGTHS OF 11' TO 23'. Various tubing lengths are available for a variety of applications. The components are adaptable to suit various configuration and capacity requirements, and solid construction and heavy gauge tubing ensures extra durability and longevity. 18 UTILITY AUGER

6. REMOTE SWING-AUGER PRODUCT OVERVIEW For 10", 13" and 16" models FEATURES Remote range of up to 400 ft - Picture [2] Remote charges using a USB plug The self-leveling hopper ensures proper weight and traction Compatible with both open and closed hydraulic systems Hopper moves into truck position within 5 seconds - Picture [4] SPECIFICATIONS MODEL >> 1050 1060 1070 1080* 1370 1385 1395* 13114 1684 16104 Size 10" x 50' 10" x 60' 10" x 70' 10" x 80' 13" x 70' 13" x 85' 13" x 95' 13" x 114' 16" x 84" 16" x 104' Tubing 12 gauge 12 gauge 1 and 2: 10 ga. 3 and 4: 11 ga. 1 and 2: 10 ga. 3, 4 and 5: 11 ga. Flighting (Measured from centre of flighting strip) 7 gauge 1/4" flighting in swing-away and main auger 1/4" on swing and main auger Flighting shaft 11 gauge, 2-3/8" diameter 11 gauge, 2-3/8" diameter - - Undercarriage 3" x 3" x 1/8" square tube 70' - 3-1/2" x 3-1/2" x 3/16" square tube; 85' and 95' - 4" x 4" x 1/4" square tube 5" x 5" x 1/4" square tube 5" x 5" x 1/4" square tube Lift arms 2" x 5" x 3/16" tube 1/4" formed tubing upper, 7 gauge lower 1/4" formed tubing Bridging 3/8" cable on 50' and 60' models, 1/2" cable on 70' and 80' models 1/2" cable Steel tube trussing Upper: 3/4" cable Upper:3/4" cable Side: 1/2" cable Wheels and hubs 15" with 5 bolt automotive type hubs and bearings 15" with 6 bolt automotive type hubs and bearings 6 bolt hubs, 11 L x 15 x 8 ply 6 bolt hubs, 11 L x 15 x 8 ply 8 bolt hubs, 16.5 L x 16.1 x 10 ply Swing auger drive Two internal gearboxes (PTO driven), sprocket and chain Two internal gearboxes (PTO driven), sprocket and chain - - Hopper dimensions 43-1/2" x 60" 43-1/2" x 60" 48" x 60" Standard hopper height from ground 15-1/4" at heel end, 14-1/4" at other end 16-3/4" at heel end, 16-1/4" at other end n/a n/a Multi-flighting hopper height from ground 11-3/4" at both ends 12-3/4" at both ends 13-1/2" 13-1/2" Tractor requirements - min PTO hp (with 540 RPM PTO) - approx. hydraulic requirements for lift 40 hp 1000 PSI 48 hp 1000 PSI 55 hp 1000 PSI 65 hp 1000 PSI 80 hp 1200 PSI 90 hp 1200 PSI 100 hp 1200 PSI 165 hp 1700 PSI 150 hp 1500 PSI 175 hp 1500 PSI Hitch weight - - 840 lb - 1140 lb 1270 lb - 2700 lb 2,200 lb 2,700 lb Weight 2,545 lb 2,987 lb 3,354 lb 3,622 lb 5,175 lb 6,381 lb 6,683 lb 15,500 lb 11,000 lb 13,000 lb ADJUSTABLE LIGHT A lighting kit, available on 16" models, provides light where it is needed most when unloading after hours. One light, located on the swing-away auger, provides light to the hopper and truck unloading area. Another light on the end of the auger tube directs light to the auger spout. The high quality, flexible spout is standard. GEARBOXES These models feature two internal gearboxes for the intake auger assembly. Easy to maintain and service, these gearboxes do not restrict auger capacity. UNDERCARRIAGE The scissor lift undercarriage, exclusive to Farm King Backsaver Augers, requires less hydraulic pressure to raise and lower the auger. The wide undercarriage is stable and solid while still meeting transport requirements. Once positioned, a shut-off valve on the underside of the auger tube limits the circulation of the hydraulics so the auger will maintain its height. DUAL SPOOL VALVE The optional two spool valve allows for hydraulic operation of the intake hopper winch and the hopper mover while only using two remote valves. The hydraulic controls eliminate the need to operate the winch and intake hopper by hand. [1] Undercarriage, 10" model shown [2] Adjustable light [3] Gearbox [4] Dual spool valve (option) [5] Auger steer (option) REMOTE SWING-AUGER [1] Adjustable light kit for models 10"-13" (standard equipment on 16" augers) [2] Remote control [3] Self-leveling hopper [4] Remotely swing the hopper in place in 5 seconds. [1] [2] [3] [5] [4] [1] [2] [3] [4] 6 BACKSAVER AUGER

19. [1] Hopper [2] Hydraulic drive with variable speed control [3] Electric-drive models have an adjustable motor mount SPECIFICATIONS MODEL >> 810H 810E 1010H 1010E Tube width 8" 8" 10" 10" Tube length 9' 9' 9' 9' Drive type Hydraulic Electric Hydraulic Electric Hydraulic requirements 12 gpm, 1200-1400 PSI - 12 gpm, 1200-1400 PSI - Motor requirements - 3 to 5 hp, 1725 RPM - 3 to 5 hp, 1725 RPM Auger tubing 16 gauge 16 gauge 16 gauge 16 gauge Flighting (Measured from centre of strip) 12 gauge 12 gauge 12 gauge 12 gauge Weight 260 lb 270 lb 310 lb 320 lb DRIVE A (up) A (down) B (up) B (down) C (up) C (down) D (up) D (down) E Hydraulic 44" 38" 65" 64" 149" 151" 15.5" 13.25" 12.5" Electric motor 42" 35.5" 52" 52" 149" 151" 15.5" 13.25" 12.5" CLEANOUT - hinged cleanout gate in the bottom of the hopper. ELECTRIC DRIVE - 12" pulley for electric drive protected by safety shield. [1] [2] [3] UNLOADING AUGER • 21 UNLOADING AUGER 8" AND 10" MODELS FARM KING UNLOADING AUGERS TRANSFER GRAINS AND OILSEEDS MUCH FASTER THAN CONVENTIONAL UTILITY AUGERS AND REACH WHERE NORMAL PORTABLE AUGERS CAN’T. The hopper of the unloading auger fits under hopper bottom bins and hopper trailers for fast and easy unloading. The weight is evenly distributed at the pivot wheels for optimum stability and balance; one person can easily move the unloading auger into position. UNLOADING AUGER PRODUCT OVERVIEW Transfers grain and oilseed faster Handheld maneuverability Reaches where normal portable augers can’t FEATURES Rubber edging on hopper to minimize spillage Even weight distribution OPTIONS Hydraulic drive and electric drive available 19 UNLOADING AUGER

Views

  • 2477 Total Views
  • 1766 Website Views
  • 711 Embedded Views

Actions

  • 0 Social Shares
  • 0 Likes
  • 0 Dislikes
  • 0 Comments

Share count

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Embeds 5

  • 1 search.google.com
  • 2 www.balepro.com.au
  • 4 103.230.158.76
  • 5 www.beulahmachinery.com.au
  • 1 www.google.com